UA-.NETStandard/samples/Robotics

Robotics samples

Three runnable samples covering the two robotics companion models this stack implements: OPC 40010 Robotics, which describes a robot, and the draft OPC UA — Robot Intent, which commands one.

Sample	What it is	What it shows
MinimalRobotServer	A server for a two-robot cell	OPC 40010 topology, RSL/GPOS positioning, and an OpenUSD representation of the whole cell
IntentEnabledRobot	A server for one collaborative arm	The Robot Intent command surface end to end, plus an OpenUSD representation you can drive
IntentViewerClient	A client with a 3-D viewport	Clicking a target in the OpenUSD viewport and watching the arm execute the intent

All three are non-production demonstration code. --insecure in the command lines below means an unsecured endpoint with blanket certificate acceptance; it exists so the samples start without a PKI dance and must never be used anywhere real.

MinimalRobotServer

A self-contained server exposing a robot cell: two KUKA-style six-axis arms on mobile platforms, their axes, power trains and safety states modelled per OPC 40010, their positions modelled per OPC 10000-210 RSL and OPC 10000-211 GPOS, and the whole thing published as an OpenUSD representation whose assets the server serves over the Part 5 FileType.

dotnet run --project samples/Robotics/MinimalRobotServer -- --host localhost --port 62830

Then render it live with the connector tool:

dotnet run --project tools/Opc.Ua.OpenUsd.Connector -- `
    --server opc.tcp://localhost:62830/MinimalRobotServer `
    --fetch-assets ./stage --insecure --view

See MinimalRobotServer/README.md for the full walkthrough, the address-space layout and the USD binding contract.

IntentEnabledRobot

One stationary UR5e-style collaborative arm with an offset wrist — deliberately a different kinematic family from the cell sample's arms — on a workbench with four target locations.

Where MinimalRobotServer shows you what a robot is, this shows you how to ask it to do something: the server declares an IntentControllerType with its capabilities, frames, tool centre point, locations, axes, outputs, kinematic description and safety state, and executes submitted intents against a simulated motion kernel with real kinematics. Every intent is tracked on a Part 10 program instance, so a motion that takes a minute outlives the Call that started it.

dotnet run --project samples/Robotics/IntentEnabledRobot -- --host localhost --port 62840

IntentViewerClient

The client connects, discovers Server/RobotIntent/Controllers, reads the controller's capabilities, opens the OpenUSD viewport on the served stage, and streams live joint and tool-centre-point values into the picture. Click one of the four target pucks on the bench and the client submits a linear-move intent to that location, then tracks the resulting IntentOperation to a terminal state while the arm animates on screen.

Start the server first, then:

dotnet run --project samples/Robotics/IntentViewerClient -- `
    --server opc.tcp://localhost:62840/IntentEnabledRobot `
    --insecure --view

It also runs headless, which is how it is exercised in CI and how it works on a machine without the native OpenUSD payload:

dotnet run --project samples/Robotics/IntentViewerClient -- `
    --server opc.tcp://localhost:62840/IntentEnabledRobot --insecure

In headless mode the four targets are offered as a console menu instead of as prims to click, and everything downstream of the pick — submission, tracking, cancellation, command authority — is identical.

Agent-driven pallet stacking

IntentViewerClient --mcp is the agent entry point for the intent sample. Start IntentEnabledRobot, then run the viewer with MCP over stdio for a headless agent or over HTTP when the OpenUSD viewport is open. The agent and the human viewer share the same OPC UA SampleSession, so MCP calls, operation monitoring, payload outputs and OpenUSD live bindings all describe the same robot.

A well-behaved agent starts with discovery, not motion:

1. robotics_list_controllers
2. robotics_read_controller to inspect SupportedIntents, SupportedFacets, frames, tools, locations and outputs
3. robotics_read_state to verify Ready, mode, safety and current command owner
4. robotics_request_control before any command

The pallet demonstration deliberately proves refusal handling before the successful plan. Another session holds command authority, the agent submits a move, receives Accepted=false with Failure=ControlNotOwned, reads the enum and message, releases or waits for the owner, requests authority itself, and only then replans. It must not retry the refused submission blindly.

The stacking plan uses the published model seam. Parts begin under /World/Payloads/BinParts, the held part is driven by HeldPartPosition and HeldPartVisible, and completed slots are driven by PayloadSlotNNFilled. The viewer and connector do not contain pallet logic; they just render the server-published bindings. The agent can pick from Bin, move the held part to row/layer coordinates near Fixture, place it, then submit a mission that repeats the sequence for the next slot.

Agents must not assume:

• command authority is implicit;
• a supported tool means the controller supports every intent kind;
• SupportedIntents, SupportedFacets, safety state or queue depth can be skipped;
• a refusal should be retried without changing the plan;
• a submitted operation is done until robotics_wait_operation or controller state says so.

How a click becomes an intent

The viewport is rendered by the optional Opc.Ua.OpenUsd.Connector.Viewer assembly. A pick becomes an intent the same way whichever path resolves it: the viewer raises UsdViewOptions.PrimPicked, and the client maps that prim path to the LocationType node the server published under the controller's Locations folder, builds an intent naming that location, and submits it.

UsdViewOptions.PickMode selects how the pick is resolved:

Mode	Behaviour
Auto (default)	Renderer-backed pointer picking first, falling back to the command prim only when renderer picking is unavailable
Renderer	Renderer-backed pointer picking only
CommandPrim	Watch UsdViewOptions.CommandPrimPath (default /World/IntentCommand) and raise the callback when its targetPrim changes

Renderer-backed picking works: the OpenUSD viewer owns input handling, DPI scaling, physical-pixel conversion and stale-revision retry, and reports hits through the host callback. Misses do not submit intents. The gaps this used to work around were filed as marcschier/openusd-dotnet issues #1, #5, #8, #9, #10 and #11, and all are fixed in the package version this sample ships against. The command-prim path remains supported and lets picking work headlessly — which is also how an MCP agent drives the same robot.

Prerequisites

• .NET SDK 10.0.
• The --view option needs the optional viewer assembly and its native OpenUSD payload, which is supported on win-x64, linux-x64, and osx-arm64. A RID-less build or publish on a supported host uses that host's payload; publish with an explicit RID for another platform. Everything else, including both servers and the headless client, runs on every platform the stack supports.

See also

• Robotics developer guide — the OPC 40010 model these servers expose.
• Robot Intent — the command surface, its lifecycle and its safety boundary.
• OpenUSD — the binding, the connector tool and the viewport.
• Relative Spatial Location and Global Positioning — how the cell sample places its robots.